Qio for Mac
Please click the arrow next to the category to expand or collapse:
Driver (6)
Firmware (2)
Manual (4)
FAQ (31)
IDArticle TitlePost Date
491 Are Sonnet Tempo SATA cards compatible with the Drobo S?Feb-02-11
Sonnet has tested the following cards with the Drobo S:
Tempo SATA E2P..............................compatible
Tempo SATA E4P..............................not compatible
Tempo SATA ExpressCard/34...........compatible
Tempo SATA Edge ExpressCard/34...compatible
Tempo SATA Pro ExpressCard/34.....not compatible
Tempo SATA X4P..............................not compatible
Qio eSATA ports...............................not compatible
 
495 My P2 card is unexpectedly unmounting from my Qio after I wake a Mac Pro or MacBook Pro from sleep.Aug-01-13
Install Qio software version 1.2.3 or later to resolve the issue.
 
499 I get a blue screen on my Mac Pro/MacBook Pro instead of booting when I connect QioMar-24-10
501 Are all C600X CF Cards more or less equal performance in a Qio?Mar-22-10
503 Can I power the Qio from a FireWire port on a MacBook Pro?Mar-23-10
509 Is the Qio driver compatible with a 64-bit kernel boot of OS X 10.6 or 10.7?Aug-01-13
Yes. Compatiblity requires Qio software version 1.2.3 or later.
 
510 Can I use the AJA IO Express with the Sonnet Qio in a MacBook Pro?Mar-23-10
Yes. Just plug the AJA ExpressCard/34 adapter into one of the Qio's two ExpressCard/34 slots.
 
512 My Qio was working fine with my ExpressCard/34 bus interface card, but the Qio does not work with my PCIe Express bus interface card in an early 2009 MacPro.Mar-31-10
514 My unibody MacBook Pro will spontaneously restart after shutdown with Qio attached.Mar-31-10
516 What kind of battery can I use with the Qio?Apr-08-10
A battery should be capable of providing 12Volts @ 3 Amps and have an XLR 4-pin power connector. Nominal power usage of Qio is 9W, and attached F2s are 8 Watts each. An example of a compatible battery is the Bescor MM7XLR-NC (BC-500 charger sold separately) that can provide 12Volts @ 7.2Amps and has a 50 Watt-hour capacity. This battery could power a Qio for 5.5 hours, or a Qio plus F2 for 3 hours.
 
527 Why does my Maci take so long to boot when the Qio is attached? Jul-31-13
528 Why can't a Mac Pro acknowledge the Qio if it is plugged in after the Mac is booted? Sep-13-13
536 With a Qio connected, my Mac Pro kernel panics when I shut down after using Avid Media Composer.Jul-31-13
547 I'm getting a OS X kernel panic when I remove an SxS card from the Qio connected to a tower Mac Pro that also has a video capture card installed.Oct-31-14
563 I'm getting a long blue screen when I boot a Mac with Qio installed.Sep-13-13
566 I upgraded to 10.6.8 and my system no longer boots.Sep-26-11
576 What version of OS X do I need to use Qio with MacBook Pro?Aug-20-14
581 Is Qio Compatible with 17" Thunderbolt MacBook Pro?Sep-13-13
632 Is Qio compatible with Echo ExpressCard/34 Thunderbolt Adapter?Jul-31-13
633 Is Qio compatible with the Matrox T/ADP Thunderbolt Port Adapter?Feb-28-12
639 Is the Qio PCIe 2.0 Bus Extender card compatible in all slots of the Mac Pro 5,1?May-06-13
646 How can I read UDF Formatted SxS cards?Aug-11-17
648 Why is the Panasonic OS X P2 driver not compatible with 64-bit mode, while the Sony SxS driver, CF driver and SATA drivers are compatible with 64-bit mode?Oct-31-14
This issue is now resolved. The Panasonic P2 driver included with Qio software version 1.2.3 and later is 64-bit compatible. Installing Qio 1.3.2 or later adds P2 support to systems running OS X in 64-bit mode, including Mavericks (10.9) and Yosemite (10.10)
 
651 Do Qio and Qio CF4 support UDMA 7 CompactFlash cards?May-06-13
653 I connected a Red Station media reader to the eSATA ports, but the media would not mount. How do I mount the media?May-06-13
Mac OS 10.7.5 will not mount FAT32 volumes connected to the eSATA ports of this device. (FAT32 volumes mount fine in 10.6.8 and in 10.8.2 and later.)

As a workaround, you can manually mount volumes with the following procedure:

1) Open terminal (Applications > Utilities > Terminal)
2) Run the following command:
diskutil list

Look for the target volume in the IDENTIFIER column. The volume will have a name like disk4s2.

3) Create a mount point by using the following terminal command:
mkdir /Volumes/myvolume

Note: myvolume is the name of the mount point you will create and must be unique - for example, you cannot mkdir /Volumes/FAT if a volume named FAT is already mounted.

4) Mount the target volume with the command:
sudo mount -t msdos /dev/disk4s2 /Volumes/myvolume

Note: disk4s2 is the from the IDENTIFIER column from step 2. myvolume is the unique name you chose in step 3.

The volume should now be mounted and is available for use. The volume must also be unmounted through terminal - finder will not be able to unmount the volume.

The command to unmount the volume is:
sudo umount /Volumes/myvolume

where myvolume is the mount point you created in step 3.
 
678 Is the Qio compatible with OS X 10.10 (Yosemite) and OS X 10.9.5 (Mavericks)?Oct-31-14
693 My computer kernel panics after updating OS X to 10.8.2. What can I do to fix it? (Qio/Qio CF4/Qio E3 issue)Nov-06-12
The OS X 10.8.2 update breaks compatibility with Qio, Qio CF4, and Qio E3 pro media readers, resulting in kernel panics on systems with Qio v1.1.6 and earlier software installed. By following the steps below, you may enable your system to work again, but the Qio will not operate after the procedure until you install Qio v1.1.8 or later software.

Process:





1. Cold-boot your computer holding the cmd and R keys together (this forces the computer to boot from the recovery partition)

2. Select the language

3. Open the Disk Utility application



  1. If your main operating system drive is locked (grayed out), select it and choose to “unlock” in the icon list at the top of the screen

  2. Note the name of the volume that holds your operating system - usually "Macintosh HD" – you will need this name later in these instructions


4. Quit Disk Utility

5. From the Utilities Menu, open the Terminal application.

6. Type the following commands, pressing the Enter key in between each command:

NOTE: In the following commands, <VOLNAME> is the name of the partition that your operating system resides on. This should have been obtained in step 3b. If your volume name has a space in it, such as "Macintosh HD", a “\” character must precede the space in the volume name (ie "Macintosh\ HD")

rm -r /Volumes/<VOLNAME>/System/Library/Extensions/STPCIFamily*

cp -rf /Volumes/<VOLNAME>/Library/Application\ Support/QIO/IOPCIFamily.kext /Volumes/<VOLNAME>/System/Library/Extensions

touch /Volumes/<VOLNAME>/System/Library/Extensions

7. Quit all applications and restart the computer.



 
713 My Qio Does Not Recognize My SD-to-SxS AdapterMay-07-13
730 I have a Retina MacBook Pro (or other Mac introduced in 2012), and my machine won't boot after installing Qio software.Dec-06-12
757 My Stardom RAIDSonic ST3620-2S-S2 is not reliable with 6Gb drives and and a 6Gb controller.Jul-08-13
The Stardom RAIDSONIC ST3620-2S-S2 is not reliable when connected at 6Gb. It was designed for 3Gb SATA. If you connected previously using a 3Gb controller, even with 6Gb drives, the connection was 3Gb. With the 6Gb controllers and 6Gb drives, the connection is negotiated at 6Gb, but the connection is not reliable because of the older design of the Stardom chassis does not support 6Gb. The drives may not be recognized or if recognized, transfers will fail at some point.
 
1135 Can I format an SxS card in UDF format in macOS?Jan-20-21
Yes, but you must use Terminal.
1) Open Terminal

2) Run
diskutil list
to get the name of the disk. It will be something like "disk4". Ejectable media are typically the last in the list.

3) Run
newfs_udf -v "My Volume Name" disk4
if disk4 was the correct one. The volume name is anything you want of course.

4) Unplug and replug the SxS card
(Due to somebody's bug, the disk will only mount after being ejected.)

5) You can run
newfs_udf
without any parameters to see other parameters that can be set.

The process can be automated somewhat by writing a bash script, which can be looked up on the internet.