|ID||Article Title||Post Date|
||Are Sonnet Tempo SATA cards compatible with the Drobo S?||Feb-02-11|
||My P2 card is unexpectedly unmounting from my Qio after I wake a Mac Pro or MacBook Pro from sleep.||Aug-01-13|
||I get a blue screen on my Mac Pro/MacBook Pro instead of booting when I connect Qio||Mar-24-10|
||Are all C600X CF Cards more or less equal performance in a Qio?||Mar-22-10|
|Sonnet measured read performance for three manufacturers' 600X (90MB/sec) CF cards in the Qio, connected to a MacBook Pro:|
Lexar Professional 600X...86MB/sec
SanDisk Extreme Pro........61MB/sec
||Can I power the Qio from a FireWire port on a MacBook Pro?||Mar-23-10|
||Is the Qio driver compatible with a 64-bit kernel boot of OS X 10.6 or 10.7?||Aug-01-13|
||Can I use the AJA IO Express with the Sonnet Qio in a MacBook Pro?||Mar-23-10|
|Yes. Just plug the AJA ExpressCard/34 adapter into one of the Qio's two ExpressCard/34 slots.|
||My Qio was working fine with my ExpressCard/34 bus interface card, but the Qio does not work with my PCIe Express bus interface card in an early 2009 MacPro.||Mar-31-10|
||My unibody MacBook Pro will spontaneously restart after shutdown with Qio attached.||Mar-31-10|
|Check the bottom of the Qio for the serial number.|
This can occur on some Qio units with a serial number begins with A, B, or C. Contact Sonnet support for more information.
||What kind of battery can I use with the Qio?||Apr-08-10|
|A battery should be capable of providing 12Volts @ 3 Amps and have an XLR 4-pin power connector. Nominal power usage of Qio is 9W, and attached F2s are 8 Watts each. An example of a compatible battery is the Bescor MM7XLR-NC (BC-500 charger sold separately) that can provide 12Volts @ 7.2Amps and has a 50 Watt-hour capacity. This battery could power a Qio for 5.5 hours, or a Qio plus F2 for 3 hours.|
||Why does my Maci take so long to boot when the Qio is attached?
||Why can't a Mac Pro acknowledge the Qio if it is plugged in after the Mac is booted? ||Sep-13-13|
||With a Qio connected, my Mac Pro kernel panics when I shut down after using Avid Media Composer.||Jul-31-13|
||I'm getting a OS X kernel panic when I remove an SxS card from the Qio connected to a tower Mac Pro that also has a video capture card installed.||Oct-31-14|
||I'm getting a long blue screen when I boot a Mac with Qio installed.||Sep-13-13|
||I upgraded to 10.6.8 and my system no longer boots.||Sep-26-11|
||What version of OS X do I need to use Qio with MacBook Pro?||Aug-20-14|
||Is Qio Compatible with 17" Thunderbolt MacBook Pro?||Sep-13-13|
||Is Qio compatible with Echo ExpressCard/34 Thunderbolt Adapter?||Jul-31-13|
||Is Qio compatible with the Matrox T/ADP Thunderbolt Port Adapter?||Feb-28-12|
|No, the Qio software is not yet compatible with a Thunderbolt connection. When Qio is compatible, it should work with the Matrox T/ADP Thunderbolt Port Adapter.|
||Is the Qio PCIe 2.0 Bus Extender card compatible in all slots of the Mac Pro 5,1?||May-06-13|
||How can I read UDF Formatted SxS cards?||Aug-11-17|
|You need to download and install the Sony SxS UDF Driver, available here http://pro.sony.com/bbsc/ssr/cat-recmedia/resource.downloads.bbsccms-assets-mkt-recmedia-downloads-upgrades.shtml|
||Why is the Panasonic OS X P2 driver not compatible with 64-bit mode, while the Sony SxS driver, CF driver and SATA drivers are compatible with 64-bit mode?||Oct-31-14|
||Do Qio and Qio CF4 support UDMA 7 CompactFlash cards?||May-06-13|
||I connected a Red Station media reader to the eSATA ports, but the media would not mount. How do I mount the media?||May-06-13|
|Mac OS 10.7.5 will not mount FAT32 volumes connected to the eSATA ports of this device. (FAT32 volumes mount fine in 10.6.8 and in 10.8.2 and later.)|
As a workaround, you can manually mount volumes with the following procedure:
1) Open terminal (Applications > Utilities > Terminal)
2) Run the following command:
Look for the target volume in the IDENTIFIER column. The volume will have a name like disk4s2.
3) Create a mount point by using the following terminal command:
Note: myvolume is the name of the mount point you will create and must be unique - for example, you cannot mkdir /Volumes/FAT if a volume named FAT is already mounted.
4) Mount the target volume with the command:
sudo mount -t msdos /dev/disk4s2 /Volumes/myvolume
Note: disk4s2 is the from the IDENTIFIER column from step 2. myvolume is the unique name you chose in step 3.
The volume should now be mounted and is available for use. The volume must also be unmounted through terminal - finder will not be able to unmount the volume.
The command to unmount the volume is:
sudo umount /Volumes/myvolume
where myvolume is the mount point you created in step 3.
||Is the Qio compatible with OS X 10.10 (Yosemite) and OS X 10.9.5 (Mavericks)?||Oct-31-14|
||My computer kernel panics after updating OS X to 10.8.2. What can I do to fix it? (Qio/Qio CF4/Qio E3 issue)||Nov-06-12|
||My Qio Does Not Recognize My SD-to-SxS Adapter||May-07-13|
||I have a Retina MacBook Pro (or other Mac introduced in 2012), and my machine won't boot after installing Qio software.||Dec-06-12|
||My Stardom RAIDSonic ST3620-2S-S2 is not reliable with 6Gb drives and and a 6Gb controller.||Jul-08-13|
|The Stardom RAIDSONIC ST3620-2S-S2 is not reliable when connected at 6Gb. It was designed for 3Gb SATA. If you connected previously using a 3Gb controller, even with 6Gb drives, the connection was 3Gb. With the 6Gb controllers and 6Gb drives, the connection is negotiated at 6Gb, but the connection is not reliable because of the older design of the Stardom chassis does not support 6Gb. The drives may not be recognized or if recognized, transfers will fail at some point.|
||Can I format an SxS card in UDF format in macOS?||Jan-20-21|