|ID||Article Title||Post Date|
||Are Sonnet Tempo SATA cards compatible with the Drobo S?||Feb-02-11|
||My P2 card is unexpectedly unmounting from my Qio after I wake a Mac Pro or MacBook Pro from sleep.||Aug-01-13|
|Install Qio software version 1.2.3 or later to resolve the issue.|
||I get a blue screen on my Mac Pro/MacBook Pro instead of booting when I connect Qio||Mar-24-10|
||Are all C600X CF Cards more or less equal performance in a Qio?||Mar-22-10|
||Can I power the Qio from a FireWire port on a MacBook Pro?||Mar-23-10|
||Is the Qio driver compatible with a 64-bit kernel boot of OS X 10.6 or 10.7?||Aug-01-13|
||Can I use the AJA IO Express with the Sonnet Qio in a MacBook Pro?||Mar-23-10|
||My Qio was working fine with my ExpressCard/34 bus interface card, but the Qio does not work with my PCIe Express bus interface card in an early 2009 MacPro.||Mar-31-10|
||My unibody MacBook Pro will spontaneously restart after shutdown with Qio attached.||Mar-31-10|
|Check the bottom of the Qio for the serial number.|
This can occur on some Qio units with a serial number begins with A, B, or C. Contact Sonnet support for more information.
||What kind of battery can I use with the Qio?||Apr-08-10|
|A battery should be capable of providing 12Volts @ 3 Amps and have an XLR 4-pin power connector. Nominal power usage of Qio is 9W, and attached F2s are 8 Watts each. An example of a compatible battery is the Bescor MM7XLR-NC (BC-500 charger sold separately) that can provide 12Volts @ 7.2Amps and has a 50 Watt-hour capacity. This battery could power a Qio for 5.5 hours, or a Qio plus F2 for 3 hours.|
||Why does my Maci take so long to boot when the Qio is attached?
||Why can't a Mac Pro acknowledge the Qio if it is plugged in after the Mac is booted? ||Sep-13-13|
||With a Qio connected, my Mac Pro kernel panics when I shut down after using Avid Media Composer.||Jul-31-13|
||I'm getting a OS X kernel panic when I remove an SxS card from the Qio connected to a tower Mac Pro that also has a video capture card installed.||Oct-31-14|
||I'm getting a long blue screen when I boot a Mac with Qio installed.||Sep-13-13|
|Reinstall the Qio software.|
||I upgraded to 10.6.8 and my system no longer boots.||Sep-26-11|
|If you have Qio 1.0.5 software installed and you upgrade to 10.6.8 you will no longer be able to boot. Sonnet strongly recommends that you install Qio 1.1 software before upgrading to 10.6.8 or 10.7. If you have installed 10.6.8 prior to installing Qio 1.0.6 or 1.1 software and are not able to boot, you can recover with the following steps:|
1) Boot Mac OS X from an external drive or DVD.
2) In the Finder, remove the spaces from the name of your system disk that won't boot. For example, rename Macintosh HD to MacintoshHD. (If your system disk has another name use that name in place of MacintoshHD in the next two steps.)
2) Launch Terminal and type:
sudo rm -r /Volumes/MacintoshHD/System/Library/Extensions/STPCIFamily.kext
sudo cp -r "/Volumes/MacintoshHD/Library/Application Support/QIO/IOPCIFamily.kext" /Volumes/MacintoshHD/System/Library/Extensions (typed all on one line)
sudo touch /Volumes/MacintoshHD/System/Library/Extensions
6) Install Qio 1.1 or greater
||What version of OS X do I need to use Qio with MacBook Pro?||Aug-20-14|
||Is Qio Compatible with 17" Thunderbolt MacBook Pro?||Sep-13-13|
||Is Qio compatible with Echo ExpressCard/34 Thunderbolt Adapter?||Jul-31-13|
||Is Qio compatible with the Matrox T/ADP Thunderbolt Port Adapter?||Feb-28-12|
||Is the Qio PCIe 2.0 Bus Extender card compatible in all slots of the Mac Pro 5,1?||May-06-13|
||How can I read UDF Formatted SxS cards?||Aug-11-17|
||Why is the Panasonic OS X P2 driver not compatible with 64-bit mode, while the Sony SxS driver, CF driver and SATA drivers are compatible with 64-bit mode?||Oct-31-14|
|This issue is now resolved. The Panasonic P2 driver included with Qio software version 1.2.3 and later is 64-bit compatible. Installing Qio 1.3.2 or later adds P2 support to systems running OS X in 64-bit mode, including Mavericks (10.9) and Yosemite (10.10) |
||Do Qio and Qio CF4 support UDMA 7 CompactFlash cards?||May-06-13|
|Yes, Qio and Qio CF4 support UDMA 7 CompactFlash cards in UDMA 6 mode.|
Background: CompactFlash Revision 6.0 (November 2010) added UltraDMA Mode 7 (167 MB/s), which is up to 20% faster than UDMA 6 (133MB/sec). All UDMA 7 CompactFlash cards are compatible with UDMA 6 cameras and readers.
The Qio's CompactFlash slots can be read concurrently. The Qio can read the fastest CF cards at up to 133MB/s each and a total aggregate of 200MB/s (two cards).
The Qio CF4 can read all four CompactFlash slots concurrently. When connected to a desktop machine, the maximum aggregate read speed is 133MB/sec (one card), 266MB/sec (two cards), 400MB/sec (three or four cards).
||I connected a Red Station media reader to the eSATA ports, but the media would not mount. How do I mount the media?||May-06-13|
||Is the Qio compatible with OS X 10.10 (Yosemite) and OS X 10.9.5 (Mavericks)?||Oct-31-14|
|The Qio is compatible with OS 10.10 (Yosemite) and 10.9.5 (Mavericks) when using Qio software version 1.3.2 and later. |
||My computer kernel panics after updating OS X to 10.8.2. What can I do to fix it? (Qio/Qio CF4/Qio E3 issue)||Nov-06-12|
|The OS X 10.8.2 update breaks compatibility with Qio, Qio CF4, and Qio E3 pro media readers, resulting in kernel panics on systems with Qio v1.1.6 and earlier software installed. By following the steps below, you may enable your system to work again, but the Qio will not operate after the procedure until you install Qio v1.1.8 or later software. |
1. Cold-boot your computer holding the cmd and R keys together (this forces the computer to boot from the recovery partition)
2. Select the language
3. Open the Disk Utility application
- If your main operating system drive is locked (grayed out), select it and choose to “unlock” in the icon list at the top of the screen
- Note the name of the volume that holds your operating system - usually "Macintosh HD" – you will need this name later in these instructions
4. Quit Disk Utility
5. From the Utilities Menu, open the Terminal application.
6. Type the following commands, pressing the Enter key in between each command:
NOTE: In the following commands, <VOLNAME> is the name of the partition that your operating system resides on. This should have been obtained in step 3b. If your volume name has a space in it, such as "Macintosh HD", a “\” character must precede the space in the volume name (ie "Macintosh\ HD")
rm -r /Volumes/<VOLNAME>/System/Library/Extensions/STPCIFamily*
cp -rf /Volumes/<VOLNAME>/Library/Application\ Support/QIO/IOPCIFamily.kext /Volumes/<VOLNAME>/System/Library/Extensions
7. Quit all applications and restart the computer.
||My Qio Does Not Recognize My SD-to-SxS Adapter||May-07-13|
|If you are using the Qio or Qio E3 connected via Thunderbolt to a Mac running OS X 10.8.2+, this is a known issue that may be fixed by installing this software patch .|
With the release of OS X 10.8.2, Apple disabled USB 2.0 drivers over Thunderbolt. Because many SD-to-SxS adapters use the ExpressCard USB interface, and Qio and Qio E3 support USB-based adapters through the ExpressCard (SxS) slots' USB interfaces, the adapters are not recognized under 10.8.2+. Sonnet's USB 2.0 Over Thunderbolt Patch for Qio/Qio E3 removes the limitation and allows your adapter to be recognized.
||I have a Retina MacBook Pro (or other Mac introduced in 2012), and my machine won't boot after installing Qio software.||Dec-06-12|
|Boot in safe mode. In Terminal, type: sudo nvram boot-args="dart=0x0" and restart. You can undo this later with the command sudo nvram -d boot-args .|
||My Stardom RAIDSonic ST3620-2S-S2 is not reliable with 6Gb drives and and a 6Gb controller.||Jul-08-13|
||Can I format an SxS card in UDF format in macOS?||Jan-20-21|
|Yes, but you must use Terminal.|
1) Open Terminal
to get the name of the disk. It will be something like "disk4". Ejectable media are typically the last in the list.
newfs_udf -v "My Volume Name" disk4
if disk4 was the correct one. The volume name is anything you want of course.
4) Unplug and replug the SxS card
(Due to somebody's bug, the disk will only mount after being ejected.)
5) You can run
without any parameters to see other parameters that can be set.
The process can be automated somewhat by writing a bash script, which can be looked up on the internet.