|ID||Article Title||Post Date|
||Are Sonnet Tempo SATA cards compatible with the Drobo S?||Feb-02-11|
||My P2 card is unexpectedly unmounting from my Qio after I wake a Mac Pro or MacBook Pro from sleep.||Aug-01-13|
||I get a blue screen on my Mac Pro/MacBook Pro instead of booting when I connect Qio||Mar-24-10|
||Are all C600X CF Cards more or less equal performance in a Qio?||Mar-22-10|
|Sonnet measured read performance for three manufacturers' 600X (90MB/sec) CF cards in the Qio, connected to a MacBook Pro:|
Lexar Professional 600X...86MB/sec
SanDisk Extreme Pro........61MB/sec
||Can I power the Qio from a FireWire port on a MacBook Pro?||Mar-23-10|
|This powering method is not officially supported because the Qio can require more power than one FireWire port's power specification. However, the single FireWire port on the unibody MacBook Pro seems to be capable of providing more power (up to 20W in our test) than its specification. In Sonnet tests under the following conditions:|
1) If Qio is used with only memory cards (SxS's or SDHC, but not ExpressCard/34 controller cards; P2 cards but not CardBus controller cards; and/or CF Cards);
2) Qio has not more than one Fusion F2 powered from the Qio; and
3) MacBook Pro is unibody model;
then the Qio plus one Fusion F2 seems to be able to be bus powered from the unibody MacBook Pro FireWire port. You would need to use the FireWire power cable provided with the Fusion F2. Sonnet does not guarantee or support this configuration.
This does not seem to work in MacBook Pro models previous to the unibody.
||Is the Qio driver compatible with a 64-bit kernel boot of OS X 10.6 or 10.7?||Aug-01-13|
|Yes. Compatiblity requires Qio software version 1.2.3 or later.|
||Can I use the AJA IO Express with the Sonnet Qio in a MacBook Pro?||Mar-23-10|
|Yes. Just plug the AJA ExpressCard/34 adapter into one of the Qio's two ExpressCard/34 slots.|
||My Qio was working fine with my ExpressCard/34 bus interface card, but the Qio does not work with my PCIe Express bus interface card in an early 2009 MacPro.||Mar-31-10|
||My unibody MacBook Pro will spontaneously restart after shutdown with Qio attached.||Mar-31-10|
||What kind of battery can I use with the Qio?||Apr-08-10|
|A battery should be capable of providing 12Volts @ 3 Amps and have an XLR 4-pin power connector. Nominal power usage of Qio is 9W, and attached F2s are 8 Watts each. An example of a compatible battery is the Bescor MM7XLR-NC (BC-500 charger sold separately) that can provide 12Volts @ 7.2Amps and has a 50 Watt-hour capacity. This battery could power a Qio for 5.5 hours, or a Qio plus F2 for 3 hours.|
||Why does my Maci take so long to boot when the Qio is attached?
|It is normal for the Mac to take a long time to boot (as long as 10 minutes) the first time after a Qio is attached. All the new drivers need to be discovered and the kernal caches built. It is important to let this initialization process complete without interruption. |
However, in some instances, the Mac takes a long time for subsequent boots as well. If this occurs, run the Qio System Uninstaller and rerun the Qio System Installer. This should clear the problem.
||Why can't a Mac Pro acknowledge the Qio if it is plugged in after the Mac is booted? ||Sep-13-13|
||With a Qio connected, my Mac Pro kernel panics when I shut down after using Avid Media Composer.||Jul-31-13|
||I'm getting a OS X kernel panic when I remove an SxS card from the Qio connected to a tower Mac Pro that also has a video capture card installed.||Oct-31-14|
||I'm getting a long blue screen when I boot a Mac with Qio installed.||Sep-13-13|
||I upgraded to 10.6.8 and my system no longer boots.||Sep-26-11|
||What version of OS X do I need to use Qio with MacBook Pro?||Aug-20-14|
||Is Qio Compatible with 17" Thunderbolt MacBook Pro?||Sep-13-13|
||Is Qio compatible with Echo ExpressCard/34 Thunderbolt Adapter?||Jul-31-13|
||Is Qio compatible with the Matrox T/ADP Thunderbolt Port Adapter?||Feb-28-12|
||Is the Qio PCIe 2.0 Bus Extender card compatible in all slots of the Mac Pro 5,1?||May-06-13|
||How can I read UDF Formatted SxS cards?||Aug-11-17|
||Why is the Panasonic OS X P2 driver not compatible with 64-bit mode, while the Sony SxS driver, CF driver and SATA drivers are compatible with 64-bit mode?||Oct-31-14|
|This issue is now resolved. The Panasonic P2 driver included with Qio software version 1.2.3 and later is 64-bit compatible. Installing Qio 1.3.2 or later adds P2 support to systems running OS X in 64-bit mode, including Mavericks (10.9) and Yosemite (10.10) |
||Do Qio and Qio CF4 support UDMA 7 CompactFlash cards?||May-06-13|
||I connected a Red Station media reader to the eSATA ports, but the media would not mount. How do I mount the media?||May-06-13|
||Is the Qio compatible with OS X 10.10 (Yosemite) and OS X 10.9.5 (Mavericks)?||Oct-31-14|
||My computer kernel panics after updating OS X to 10.8.2. What can I do to fix it? (Qio/Qio CF4/Qio E3 issue)||Nov-06-12|
||My Qio Does Not Recognize My SD-to-SxS Adapter||May-07-13|
||I have a Retina MacBook Pro (or other Mac introduced in 2012), and my machine won't boot after installing Qio software.||Dec-06-12|
|Boot in safe mode. In Terminal, type: sudo nvram boot-args="dart=0x0" and restart. You can undo this later with the command sudo nvram -d boot-args .|
||My Stardom RAIDSonic ST3620-2S-S2 is not reliable with 6Gb drives and and a 6Gb controller.||Jul-08-13|
||Can I format an SxS card in UDF format in macOS?||Jan-20-21|
|Yes, but you must use Terminal.|
1) Open Terminal
to get the name of the disk. It will be something like "disk4". Ejectable media are typically the last in the list.
newfs_udf -v "My Volume Name" disk4
if disk4 was the correct one. The volume name is anything you want of course.
4) Unplug and replug the SxS card
(Due to somebody's bug, the disk will only mount after being ejected.)
5) You can run
without any parameters to see other parameters that can be set.
The process can be automated somewhat by writing a bash script, which can be looked up on the internet.